V-ZUG Australia Collection 2026 - Catalog - Page 84
V-ZUG Ltd
Planning aid
J001059-R28
International collection
Kitchen appliances
V-ZUG Ltd, Industriestrasse 66, CH-6302 Zug
service-support@vzug.com, www.vzug.com
06.06.19
GAS 641GS
9.5
Surface-mounted
installation
with «DualDesign»
Surface-mounted
installation
with DualDesign
Valid for article number:
Ri
571
3107165405
Y
S* ≥81
V-ZUG Ltd
1
50
Y–Y
Planning aid
J001059-R28
International collection
Kitchen appliances
06.06.19
A
B
V-ZUG Ltd, Industriestrasse 66, CH-6302 Zug
service-support@vzug.com, www.vzug.com
H
H
Y
0
≥5
T ≥90
Drawer/
cabinet
560±
1
1
0±
49
Side panel
Ra
50
0
≥
V-ZUG
Ltd
60
J001059-R28
06.06.19
A
600
Planning aid
International collection
Kitchen appliances
V-ZUG Ltd, Industriestrasse 66, CH-6302 Zug
service-support@vzug.com, www.vzug.com
* 9.6
The required
must be
observed!
Flushclearance
installation
with
«DualDesign»
≥30 mm
B
H
Corner radius Ra/Ri
≥95 mm
94 mm
0–5/1.5 mm
+1
GAS641GSAZ
8.5 0
Flush
Type installation with DualDesignA Depends on producer
Ri
Ra
Worktop depth
8.5 -10
571
Required clearance for service replacement
over
the
entire
cut-out
area.
Y
Dimension from the top of the work surface to the underside of the gas connection
Corner radii of appliance Y
Ra
Outer corner R0–5
radii of cut-out
Minimum distance between the top of the work surface and any drawerC
Minimum distance between the cut-out in 1the back and Detail
any drawer
8.5 -00 Z
Ra
50
.5
8.5 -10
+1
8.5 0
+1
8.5 0
D
H
A
B
H
Ri
S
T
5
1.
R0–5
≥4
D
C
Steel angle bonded
or screw mounted
577±
8
5
5
Y–Y
A
B
0
60
H
S* ≥85
Z
1.
≥4
8.5 0
+1
1
1
±
07
* The required
60 clearance must be observed!
1
A
T ≥90
Drawer/
Front and rear struts may be reinforced oncabinet
the underside. The
strut
width is determined by the producer of the stone
Side
panel
0
worktop. The minimum strut width can vary according to the property of the stone.
* The required
clearance
observed!
2
For
niche must
widthbe
900
mm, cut-outs in side walls left/right are necessary for servicing work where the appliance base
* The required
clearance
must
be
observed
must
be
removed
from
below. on producer
Type
A Depends
B
H
Corner radius Ra/Ri
C/D
Type
GAS641GSAZ
GAS411GSAZ/GSBZ,
Type
A
Worktop
depth
A Depends
on producer
≥30
mm
≥175 mm
B mm
98
≥30 mm on producer
≥175Bmm
A Depends
H 5/1.5 mm
Corner radius
Ra/Ri
560/490
mm
98 mm
C/D
5/1.5 mm
H
C/D
373/490
mm
Corner
radius Ra/Ri
GAS421GSAZ/GSBZ
B
Required clearance for service replacement over the entire cut-out area.
GAS641GSAZ
30underside
mm
≥ 95 mm
H
Dimension
from the top of the work surface to ≤
the
of the gas connection
GAS951GSAZ/GSBZ
Surface-mounted
installation
Ri
Corner radii of
appliance with DualDesign
Ra
Outer corner radii of cut-out
S
Minimum
distancedepth
between the top of the work surface and any drawer
A
Worktop
GAS641GSAZ
≤ 30and
mmany
≥ 175area.
mm
T
Minimum
distance between
the
in replacement
the back
B
Required
clearance
forcut-out
service
overdrawer
the entire cut-out
Flush installation
with DualDesign
560/490 mm
H
Dimension from the top of the work surface to the underside of the gas connection
Ri
Corner radii of appliance
Ra
Outer corner radii of cut-out
S
Minimum distance between the top of the work surface and any drawer
A Worktop
T depth
Minimum distance between the cut-out in the back and any drawer
B Required clearance for service replacement over the entire cut-out area.
H Measurement from the top of the work surface to the underside of the gas connection
Ri Corner radii of appliance
Ra Outer corner radii of cut-out
S Minimum distance between the top of the work surface and any drawer
T Minimum distance between the cut-out in the back and any drawer
82
94 mm
63 886/490 mm
5/1,5 mm
98 mm
5/1,5 mm
